Mac mini late 2012 data doubler

Use the flat end of a spudger to pry the hard drive connector up from its socket on the logic board. Use the tip of a spudger to lift the IR sensor connector up and out of its socket on the logic board. To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red.

Data Doubler Optical Bay HD/SSD Mounting Kit Mac Mini - EUR - OWCshop

Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board. Be sure it makes contact with the top side of outer case below the logic board before proceeding. Carefully slide the logic board assembly out of the mini, minding any cables that may get caught. Pull the hard drive away from the front edge of the mini and remove it from the outer case.

During reassembly, there are two pins on the inside edge of the hard drive that fit into the case. The holes have rubber grommets around them, so it may be difficult to tell when you have seated the hard drive correctly. There are two pairs of holes in the case. Insert the pins into the holes closest to the bottom of the case. Remove the 7. During reassembly, ensure the cables that run alongside the hard drive are tucked under the power supply. This will ensure the hard drive is properly seated. In addition, the antenna screw holes will not line up if there are cables in the way.

Pull the silver metal AC-In socket retainer away from the side of the outer case and remove it from the mini. During reassembly, notice that the silver clip hugs either side of the lower beveled edge of the AC connector. When sliding the clip back in it will hit a stop, but not click into place.

Top Selling Products

You will know that you did it correctly because it will not easily move out of position. The following steps will guide you through installing a second hard drive in your mini. In the next few steps you will be installing the grommets in the holes located along the brackets boxed in red. While working from the inner side of the bracket, push the grommet through the hole in the side of the bracket.

Be sure the grommet is seated nicely in the bracket as seen in the third picture.

Upgrading a 2012 Mac Mini to a fusion drive - raw videos shot on spec

Repeat the process for the remaining three grommets on either sides of the brackets. The bracket with all four grommets installed should look like the bracket shown in this picture. Bend the ribbon cable along the dotted lines to help the connectors remain seated in their sockets. Bend the ribbon cable 90 degrees at the SSD connector so that it is parallel to the connector. Use the edge of the SSD connector to put a 90 degree downward bend in the cable along the first large dotted line. Hold the ribbon cable on either side of the first small dotted line and bend it up 90 degrees.

Attach the cable included in the kit to your second hard drive. In our case, we are using an SSD. If your cable came with a small piece of black tape with rounded corners, you can install it over the hard drive cable connector to secure the connector to its socket on the hard drive. The piece of tape is not required and not installing it will have no adverse effects on your machine's performance.

Before attaching the cable to your hard drive make sure it has been properly folded along the dotted white lines. This will help the cable attach and stay in-place. Use a T6 Torx screwdriver to install two of the set screws on the side of the hard drive closest to the end of the hard drive cable that attaches to the logic board. Tighten the screws until they contact the end of the threaded holes in the side of the hard drive.

They are shown correctly installed in the third picture. When inserting the hard drive, be sure to place it in its bracket cable side up with the SATA connector closest to the bulge in the bracket seen in the third picture. Push the set screws into the grommets in the bracket and install the hard drive up into its bracket as seen in the second picture.

Apple Footer

Use a T6 Torx screwdriver to install the remaining two set screws through the grommets and into the side of the hard drive. Be sure that the mounting holes line up with the threaded holes in the outer case as seen in the second picture. When the logic board is installed, simply connect the second hard drive cable to the free socket on the logic board.


  1. mac cosmetics store hours chicago.
  2. Introduction.
  3. sd card recovery tools mac.
  4. mac os x calendar subscriptions!
  5. OWC Data Doubler Optical Bay Hard Drive/SSD Mounting Solution for Mac Mini - blitz micro;
  6. OWC Data Doubler Optical Bay Hard Drive/SSD Mounting Solution for Mac Mini 2009.
  7. jvm not found mac os x.

The second hard drive cable should lay flat between the two hard drives. If the second hard drive cable is placed on top of the first, the antenna plate will not reattach, and you could damage your cable.

Dual hard drive data doubler

When you start up your machine, you'll see both drives are recognized by the mini. Xbench scores show that if you install hard drives in either the top or the bottom position, their speeds will remain the same. To minimize the amount of work necessary when adding an SSD to be used as your primary drive, we recommend installing the SSD like we did in this guide and leaving the stock platter drive in its original bottom position closest to the antenna plate. Then install Lion on your SSD. Cancel: I did not complete this guide. Badges: I tried first as said in this guide, but the whole system got very unstable, the SSD was basicly unusable with lots of read errors, kernel panics etc After switch everything went smoothly.

I tried both the "upper" and "lower" ports, neither work. It's just OS X I've contacted OCZ support. Same for me as for marcojohansson. While my SSD worked in the "empty" bay, I was experiencing frequent system hangs and beach balling. Moving the SSD to the original hard drive position, and the hard drive into the extra bay seems to have solved the problem entirely!

Includes bracket, screws, toolkit, and detailed installation guide for a complete all-in-one kit. Includes everything needed to replace your optical drive with a second drive or Solid State Drive. Specifications Product Specifications. Mac mini Mid June, Includes Includes:. Advanced Search. OWC External Storage.

OWC Memory. Mac Pro. MacBook Pro "Unibody". Mac Mini. Drive Docking Solutions.

Highlights

Expansion Cards. Thunderbolt 2. Thunderbolt 3.